SNAP-PAC-R1
The SNAP-PAC-R1 programmable automation controller provides control, communication, and I/O processing in a compact, rack-mounted package. Used with the included ioProject Basic software suite (or ioProject Profes-sional, purchased separately), the Ethernet-based SNAP-PAC-R1 can handle almost all your industrial control, remote monitoring, and data aquisition needs.
 
 

Processor

200 MHz 32-bit ColdFire® 5475 with integrated floating-point unit (FPU)

Memory
  Total RAM
  Battery-backed RAM
  Flash


16 MB (5 MB available for ioControl strategy; 2 MB available for file storage)
2 MB
8 MB (3.25 MB available for ioControl strategy;
384 KB available for file storage)

Backup battery

3-volt CR2032 Lithium, user replaceable
Typical service life with power off: 5 years

Communication
  Ethernet (host and I/O)

  RS-232 serial (host only)


Two independent 10/100 Mbps Ethernet network interfaces (RJ-45 connectors)
Each interface has a separate IP address.
*One RS-232 serial port with hardware handshaking

I/O unit compatibility

Ethernet-based I/O units: Opto 22 SNAP Simple I/O, SNAP Ethernet I/O, SNAP Ultimate I/O,
and SNAP PAC R-series I/O units

Power requirements

5.0 to 5.2 VDC @ 1.2 A

Environmental
  Operating temperature
  Storage temperature
  Humidity


oC to 60 oC
-40 oC to 85 oC
0% to 95% relative humidity, non-condensing

Software
  ioProject Basic

  ioProject Professional


Includes programming, HMI software, and configuration software;
included with purchase of controller.
ioProject Basic plus OPC 2.0-compliant OPC server,
OptoControl strategy and OptoDisplay project importing,
and Ethernet link redundancy or network segmenting support.

Other features

• Multiple protocol support including TCP/IP, FTP, Modbus/TCP, SNMP,
  OptoMMP™, and SMTP
• Built-in I/O processor
• Real-time clock
• FTP server/client with file system
• Scratch Pad area for peer-to-peer communication
• Configurable link redundancy or segmented networking
  for I/O-controller subnetting (when using ioProject Professional)

*The serial connector can beused for a modem connection using PPP. This connector can also be used for a direct connection to a serial device; communication is handled through ioControl.

 
 
 
  SNAP-PAC-R2
The SNAP-PAC-R2 programmable automation controller provides control, communication, and I/O processing in a compact, rack-mounted package. Used with the included ioProject Basic software suite (or ioProject Profes-sional, purchased separately), the Ethernet-based SNAP-PAC-R2 can handle almost all your industrial control, remote monitoring, and data aquisition needs.
 
 

Processor

200 MHz 32-bit ColdFire® 5475 with integrated floating-point unit (FPU)

Memory
  Total RAM
  Battery-backed RAM
  Flash


16 MB (5 MB available for ioControl strategy; 2 MB available for file storage)
2 MB
8 MB (3.25 MB available for ioControl strategy;
384 KB available for file storage)

Backup battery

3-volt CR2032 Lithium, user replaceable
Typical service life with power off: 5 years

Communication
  Ethernet (host and I/O)

  RS-232 serial (host only)


Two independent 10/100 Mbps Ethernet network interfaces (RJ-45 connectors)
Each interface has a separate IP address.
*One RS-232 serial port with hardware handshaking

I/O unit compatibility

Ethernet-based I/O units: Opto 22 SNAP Simple I/O, SNAP Ethernet I/O, SNAP Ultimate I/O,
and SNAP PAC R-series I/O units

Power requirements

5.0 to 5.2 VDC @ 1.2 A

Environmental
  Operating temperature
  Storage temperature
  Humidity


oC to 60 oC
-40 oC to 85 oC
0% to 95% relative humidity, non-condensing

Software
  ioProject Basic

  ioProject Professional


Includes programming, HMI software, and configuration software;
included with purchase of controller.
ioProject Basic plus OPC 2.0-compliant OPC server,
OptoControl strategy and OptoDisplay project importing,
and Ethernet link redundancy or network segmenting support.

Other features

• Multiple protocol support including TCP/IP, FTP, Modbus/TCP, SNMP,
  OptoMMP™, and SMTP
• Built-in I/O processor
• Real-time clock
• FTP server/client with file system
• Scratch Pad area for peer-to-peer communication
• Configurable link redundancy or segmented networking
  for I/O-controller subnetting (when using ioProject Professional)

*The serial connector can be used for a modem connection using PPP. This connector can also be used for a direct connection to a serial device; communication is handled through ioControl.

 
 
 
  SNAP-PAC-S1
The SNAP-PAC-S1 programmable automation controller provides powerful, real-time control and communications to meet your industrial control, moni-toring, and data acquisition needs.

Use the SNAP-PAC-S1 with SNAP Ethernet I/O units and ioProject software to form a complete control system that includes digital and analog control, serial string handling, PID loops, and enterprise connectivity.

The controller is compact and industrially hardened. It includes two indepen-dent Ethernet network interfaces with separate IP addresses, which can be used to segment the control network from the company network or for redun-dant Ethernet links.

The SNAP-PAC-S1 also has three serial ports: an RS-232 port with full hard-ware handshaking, ideal for PPP communication using a modem; another RS-232 port for connecting directly to serial devices; and an RS-485 port for connecting to legacy mistic I/O units.
 
 

Processor

266MHz 32-bit ColdFire®5475 with integrated floating-point unit (FPU)

Memory
   Total RAM
   Battery-backed RAM
   Flash EEPROM


32 MB (16 MB available for ioControl strategy)
8 MB
16 MB (7.5 MB available for ioControl strategy; 4 MB available for file storage)

Backup battery

User-replaceable 3.6-volt TL 5242 /W lithium, 10-year minimum power-off data retention

Communication
Ethernet (host and I/O)

RS-232 serial (host only)

RS-485 serial (I/O only)

Two independent 10/100 Mbps Ethernet network interfaces (RJ-45 connectors).
Each interface has a separate IP address.
Two RS-232 serial ports (one DB-9 and one pluggable connector);
one port has full handshaking.
One RS-485 serial port (pluggable connector); two-wire RS-485; no mistic signal interrupts

I/O unit compatibility
Ethernet-based I/O units
Serial-based I/O units

Opto 22 SNAP Simple I/O, SNAP Ethernet I/O, and SNAP Ultimate I/O units
Serial B3000, SNAP-BRS, B100/B200, mistic remote bricks (G4D16R, G4D32RS, G4A8R)

Power requirements

8-32 VDC ±0.5, 10 VA maximum
(SNAP-PAC-S1 controllers with serial numbers below 500,000 use 8-24 VDC)

Environmental
Operating temperature
Storage temperature
Humidity

0 oC to 60 oC
-40 oC to 85 oC
0% to 95% relative humidity, non-condensing

Software
ioProject Basic

ioProject Professional

Includes programming, HMI software, and configuration software;
included with purchase of controller.
ioProject Basic plus OPC 2.0-compliant OPC server,
OptoControl strategy and OptoDisplay project importing,
support for serial mistic I/O units, and Ethernet link redundanancy support.

Other features

Multiple protocol support including TCP/IP, FTP, and OptoMMP™.
Real-time clock
FTP server/client with file system
Ethernet link redundancy or network segmenting

 
 
 
  SNAP-UP1-ADS

The SNAP Ultimate controller/brain is a programmable I/O and communi-cations processor. It can be used as a rack-mounted controller or as an I/O unit in a larger control system based on a more powerful Opto 22 controller, such as the SNAP-PAC-S1.

Used as a rack-mounted controller, the SNAP-UP1-ADS is programmed using the ioProject Basic software suite, which is included in the purchase price.

NOTE: For new development, we recommend the SNAP-PAC-R1 on-the-rack controller instead. This new controller has the same features as SNAP Ultimate I/O but is more powerful and less expensive. The SNAP-PAC-R1 uses a SNAP M-series rack. To compare features, see both the SNAP Controller Comparison Chart and the SNAP Ethernet Brains and On-the-Rack Controllers Comparison Chart.

 
 

Power Requirements

  5.0VDC ±0.1VDC, 최대 1.2A (모듈 공급전원 제외)

Processor

  32-bit ColdFire 5407

Memory:
  Total RAM
  Battery-backed RAM
  Flash EEPROM


  16 MB
  512 KB
  8 MB

Backup battery

  CR2032, fixed (not user replaceable)

Network Interface

  IEEE 802.3 network, 10Base-T and 100Base-TX

Serial Port

  RS-232

Serial Data Rates

  Default is 19,200 kBd; baud rate is soft-selectable from 150 to 115,200 kBd.

Maximum Ethernet Segment Length

  100 meters with Category 5 or superior UTP.
  For 100 Mbps at this distance, use Category 5 or superior solid UTP.

Jumpers (Internal)

  Boot to kernel/boot to loader
  Reset to factory defaults

Temperature:
  Operating
  Storage


  0 °C to 70 °C
  -40 °C to 85 °C

Humidity

  0–95% humidity, non-condensing

 
 
 
  SNAP-UP1-D64
The SNAP-UP1-D64 controller/brain is a programmable I/O and communica-tions processor. It can be used as a rack-mounted controller or as an I/O unit in a larger control system based on a more powerful Opto 22 controller, such as the SNAP-PAC-S1.

Used as a rack-mounted controller, the SNAP-UP1-ADS is programmed using the ioProject Basicsoftware suite, which is included in the purchase price. As an I/O processor, the brain has simple digital capability only. It handles 4-channel SNAP digital modules only and is not compatible with 32-channel digital I/O.
 

Power Requirements

5.0 VDC ± 0.1 VDC at 1.2 A maximum (does not include module power requirements)

Processor

32-bit ColdFire 5407

Memory:
  Total RAM
  Battery-backed RAM
  Flash EEPROM


16 MB
512 KB
8 MB

Backup battery

CR2032, fixed (not user replaceable)

Network Interface

IEEE 802.3 network, 10Base-T and 100Base-TX

Serial Port

RS-232

Serial Data Rates

Default is 19,200 kBd; baud rate is soft-selectable from 150 to 115,200 kBd.

Maximum Ethernet Segment Length

100 meters with Category 5 or superior UTP.
For 100 Mbps at this distance, use Category 5 or superior solid UTP.

Jumpers (Internal)

Boot to kernel/boot to loader
Reset to factory defaults

Temperature:
  Operating
  Storage


0 °C to 70 °C
-40 °C to 85 °C

Humidity

0–95% humidity, non-condensing

 
 
 
  SNAP-UP1-M64
The SNAP-UP1-M64 controller/brain is a programmable I/O and communica-tions processor. It can be used as a rack-mounted controller or as an I/O unit in a larger control system based on a more powerful Opto 22 controller, such as the SNAP-PAC-S1.

Used as a rack-mounted controller, the SNAP-UP1-M64 is programmed using the ioProject Basic software suite, which is included in the purchase price. As an I/O processor, the brain has simple digital, analog, and serial capability.

NOTE: For new development, we recommend the SNAP-PAC-R2 on-the-rack controller instead. This new controller has the same features as the SNAP-UP1-M64 but is more powerful and less expensive. To compare features, see both the SNAP Controller Comparison Chart and the SNAP Ethernet Brains and On-the-Rack Controllers Comparison Chart.
 
 

Power Requirements

5.0 VDC ±0.1 VDC at 1.2 A maximum (does not include module power requirements)

Processor

32-bit ColdFire 5407

Memory:
  Total RAM
  Battery-backed RAM
  Flash EEPROM


16 MB
512 KB
8 MB

Backup battery

CR2032, fixed (not user replaceable)

Network Interface

IEEE 802.3 network, 10Base-T and 100Base-TX

Serial Port

RS-232

Serial Data Rates

Default is 19,200 kBd; baud rate is soft-selectable from 150 to 115,200 kBd.

Maximum Ethernet Segment Length

100 meters with Category 5 or superior UTP.
For 100 Mbps at this distance, use Category 5 or superior solid UTP.

Jumpers (Internal)

Boot to kernel/boot to loader
Reset to factory defaults

Temperature:
  Operating
  Storage


0 °C to 70 °C
-40 °C to 85 °C

Humidity

0–95% humidity, non-condensing

 
 
 
  SNAP-PACLC
The SNAP PAC Learning Center is a fully functional, complete package of Opto 22 hardware and software that provides everything you need to learn about Opto 22’s SNAP Ethernet-based systems. The Learning Center in-cludes ioProject Basic software, a SNAP-PAC-R1 rack-mounted controller, SNAP I/O modules and mounting rack, and a load panel with digital and analog sensors and actuators (switches, LEDs, a temperature probe, a meter, and so on).

The included step-by-step tutorial guides you through the hardware assem-bly and software installation and gives you hands-on programming experi-ence with the ioProject software. You will configure I/O points, read and write to those points, create several flowcharts as part of a control strategy, and build a graphical user interface.

Because the SNAP PAC Learning Center consists of the same field-proven, real hardware and software used by Opto 22 customers all over the world, you'll be able to apply not only the knowledge you've learned, but also the actual Learning Center hardware and software in your next automation project.
 
 

Included Components

  • ioProject Basic software
  • SNAP-PAC-R1 controller
  • SNAP-M32 8-position module mounting rack
  • Five SNAP I/O modules (two digital, three analog)
  • Learning Center load panel
  • Power cable (three-prong, 120 VAC)
  • Ethernet Category 5 crossover cable
  • SNAP PAC Learning Center Guide (printed)
  • Complete ioProject documentation (in PDF format)
 최소 요구사항

     A computer with at least the minimum processor required for your version of Microsoft Windows (1 GHz     Pentium®class or better recommended) and Ethernet capability
  • VGA or higher resolution monitor (Super VGA recommended). Minimum size: 800x600 with small fonts.
  • Mouse or other pointing device
  • Installed Windows printer (optional)
  • Microsoft Windows XP or Windows 2000® (with SP4) workstation operating system
  • At least 128 MB RAM (256 MB recommended)
  • At least 89 MB of available hard drive space
 
 
 
  SNAP-LCE
The SNAP-LCE is a stand-alone, small-footprint, Ethernet industrial controller designed for use with SNAP Ethernet I/O units and the ioProject software suite. The SNAP-LCE provides real-time control and is used primarily in industrial control applications. It is programmed with the included ioControl, Opto 22's popular flowchart-based control programming software.

For new applications, also look at the newer standalone SNAP-PAC-S1 and the rack-mounted SNAP-PAC-R1 controllers. SNAP PACs also run ioProject software but provide additional power and network connections. Compare controller features using the SNAP Controller Comparison Chart.
 
 

Processor

32-bit ColdFire® 5407

Memory
   Total RAM
   Battery-backed RAM
   Flash EEPROM


16 MB
512 KB
8 MB

Backup battery

3-volt CR2032 Lithium, user replaceable.
Typical service life with power off: 5 years.

Host communication

Ethernet (10/100 Mbps) or PPP (dial-up and radio modem)

I/O communication

Ethernet (10/100 Mbps)

I/O unit compatibility

Opto 22 SNAP Simple I/O, SNAP Ethernet I/O, and SNAP Ultimate I/O units

Serial ports

Two RS-232 ports. Baud rate is soft-selectable from 150–115,200 kBd.

Power requirements

5.0 to 5.2 VDC at 1.2 A

Operating temperature

0 oC to 60 oC

Storage temperature

-40 oC to 85 oC

Humidity

0% to 95% relative humidity, non-condensing

Software

ioProject software suite (ioControl, ioDisplay, ioManager)
Purchase OptoOPCServer separately to communicate using OPC.

Other features

FTP server/client with file system
Real-time clock

 
 
 
  SNAP-LCSX
The SNAP-LCSX controller provides powerful real-time industrial control in a small footprint. It is designed to work with the FactoryFloor software suite and with SNAP brains, racks, and analog and digital SNAP I/O modules. Top-mounted serial ports include a dedicated Opto 22 remote I/O port and one RS-232 or RS-485 serial port. A 5 VDC power supply is required.

NOTE: The SNAP-LCSX is NOT compatible with the ioProject Software suite.
 

Item

Specification

CPU

32-bit Motorola 68EC020 processor

CPU clock frequency

16.67 MHz

Memory
RAM
Flash ROM

1 MB with battery backup
256 KB

RAM/clock battery

3.6-volt lithium, non-rechargeable

I/O

Opto 22 remote I/O using RS-485

Communication

COM 0: jumper selectable as RS-232 or RS-485, 2-wire or 4-wire. Modem control signals are present for RS-232 (RTS, CTS, DTR, DCD, and RI). Pull-up, pull-down, and termination are jumper selectable for RS-485 operation, allowing multidrop operation.
COM 1: dedicated Opto 22 remote I/O port (2-wire RS-485 with interrupt capability)
COM 2 and COM 3: (LCSX-PLUS only): jumper selectable RS-232 or RS-485.
RS-232 signals include TX, RX, RTS, and CTS. RS-485 is either 2-wire or 4-wire, with selectable termination and biasing.
Note: All ports use low-noise slew-rate-limited drivers and are transient protected to 400W.

Real-time clock

Clock/calendar, Epson 64613 with battery backup

Other features

Multiple protocol support including TCP/IP, FTP, and OptoMMP™.
Real-time clock
FTP server/client with file system
Ethernet link redundancy or network segmenting

 
 
 
  SNAP-LCSX-PLUS
The SNAP-LCSX-PLUS controller provides powerful real-time industrial control in a small footprint. It is designed to work with the FactoryFloor software suite and with SNAP brains, racks, and analog and digital SNAP I/O modules. Top-mounted serial ports include a dedicated Opto 22 remote I/O port and three RS-232 or RS-485 serial port. A 5 VDC power supply is required.

NOTE: The SNAP-LCSX-PLUS is NOT compatible with ioProject software.
 
 

Item

Specification

CPU

32-bit Motorola 68EC020 processor

CPU clock frequency

16.67 MHz

Memory
RAM
Flash ROM

1 MB with battery backup
256 KB

RAM/clock battery

3.6-volt lithium, non-rechargeable

I/O

Opto 22 remote I/O using RS-485

Communication

COM 0: jumper selectable as RS-232 or RS-485, 2-wire or 4-wire. Modem control signals are present for RS-232 (RTS, CTS, DTR, DCD, and RI). Pull-up, pull-down, and termination are jumper selectable for RS-485 operation, allowing multidrop operation.
COM 1: dedicated Opto 22 remote /O port (2-wire RS-485 with interrupt capability)
COM 2 and COM 3: (LCSX-PLUS only): jumper selectable RS-232 or RS-485.
RS-232 signals include TX, RX, RTS, and CTS. RS-485 is either 2-wire or 4-wire, with selectable termination and biasing.
Note: All ports use low-noise slew-rate-limited drivers and are transient protected to 400W.

Power requirements
5VDC +/- 5% at 500 mA (maximum)
Typical operating temperature 0 °C to 70 °C
Storage temperature
-40 °C to 85 °C
Humidity
5% to 95% relative humidity, non-condensing

Software

FactoryFloor (OptoControl, OptoDisplay, OptoServer, and OptoConnect) and Classic software (Cyrano, Mistic MMI, and MDS)

System monitor

Processor and power watchdog timers

 
 
 
  SNAP-LCM4 
The SNAP-LCM4 is a powerful industrial controller that provides real-time control and communication to I/O systems, serial devices, motion control-lers, and networks. The SNAP-LCM4 is designed to work with the Factory Floor software suite. The controller includes three serial ports and provides 10/100 Mbps Fast Ethernet and ARCNET communication options through four expansion slots. The SNAP-LCM4 is NOT compatible with the ioProject Software suite.

NOTE: For new applications, we recommend the SNAP-PAC-S1standalone controller and the ioProject software suite instead of the SNAP-LCM4 and FactoryFloor. SNAP PAC S-series controllers offer a migration path for legacy mistic systems.

Compare controller features using the SNAP Controller Comparison Chart.
 

CPU

IEEE floating-point math co-processor

Memory:
RAM
Flash EEPROM

4 MB with battery backup (user programs and data), not expandable
2 MB (controller firmware and user programs), not expandable

RAM/clock battery

3.6-volt lithium, non-rechargeable

Communication, base unit

Three RS-232 or RS-485 ports, one dedicated RS-485 remote I/O port
with interrupt capability

Real-time clock

Clock/calendar, Epson 64613 with battery backup, Y2K compliant

Power requirements

5VDC ±0.1 VDC at 1 Amp (maximum) without expansion cards

Typical operating temperature

0 °C to 70 °C

Storage temperature -40 °C to 85 °C
Humidity
5% to 95% relative humidity, non-condensing
Software
FactoryFloor (OptoControl, OptoDisplay, OptoServer, and OptoConnect)
and Classic software (Cyrano, Mistic MMI, and MDS)

Hard system monitors
(including watchdog timer and
voltage monitor)

Detect main power supply operation and proper microprocessor operation

Soft system monitors

Program/data corruption
Host and I/O communication

주소: (121-758) 서울특별시 마포구 공덕동 256-13 제일빌딩 1101호 세경데이타시스템(주)
Tel: (02)703-2999 / Fax: (02)703-8558 Copyright(C) 1998-2007 세경데이타시스템(주) All rights reserved.